Interact with this product in a Layout Tool:
Features
- Single card fiber optic receiver for one composite analog, SDI or HD-SDI video and four analog or AES signals
- Auto-sensing (analog or digital) video and audio outputs
- Supports 525/625 line component 4:2:2 SDI @ 270Mb/s
- Supports HD (SMPTE ST 292-1) video @ 1.485Gb/s
- Supports both NTSC and PAL analog, or 4:2:2 component digital video
- Supports Analog to Digital and Digital to Analog audio conversion
- Broadcast quality analog video and audio performance
- Meets or exceeds EIA/TIA RS250-C short haul specifications for analog video and audio transport
- Supports 32, 44.1, 48KHz AES audio
- Dolby E™ compatible
- Adjustable gain, DC offset and pre-emphasis for driving up to 250m of Belden 1694 coaxial cable
- Fully hot-swappable from front of frame with no fiber disconnect/reconnect required
- Supports single-mode and multi-mode fiber optic cable
- Wideband optical input (1270nm - 1610nm)
- Comprehensive signal and card status monitoring via four-digit card-edge display, or remotely through SNMP and VistaLINK® capability
- VistaLINK® capable for remote monitoring via SNMP (using VistaLINK® PRO) when installed in 7800FR frame with a 7800FC VistaLINK® Frame Controller
Specifications
Analog Video Output | |
|---|---|
| Standard | NTSC (SMPTE ST 170), PAL (ITU-R 624-2) |
| Number of Outputs | 2 |
| Connector | BNC per IEC 61169-8 Annex A |
| System Bandwidth | > 5.5MHz |
| Output Level | 1V p-p (nominal), 2V p-p (maximum) |
| Gain | Unity gain nominal, adjustable 50% to 150% |
| Impedance | 75Ω |
| Return Loss | > 30dB to 5.5MHz |
| SNR | > 70dB |
| Differential Gain | < 1.0% |
| Differential Phase | < 0.7° |
| Pre-emphasis | Adjustable cable loss compensation for up to 250m of Belden 1694 |
| Passband Ripple | |
| NTSC | < ±0.1dB to 4.1MHz < ±0.2dB to 5.5MHz |
| PAL | < ±0.1dB to 4.8MHz < ±0.2dB to 5.8MHz |
| Chroma/Luma Gain | 98% to 103% |
| Chroma/Luma Delay | |
| NTSC | < 5ns |
| PAL | < 12ns |
| Line Time Distortion | 1.2% |
Serial Video Output | |
|---|---|
| Standard | SMPTE ST 259-C, 525 or 625 line components SMPTE ST 305 (SDTi), DVB-ASI (without separate audio), SMPTE ST 292-1 (HD) |
| Number of Outputs | 2 regenerated |
| Connector | BNC per IEC 61169-8 Annex A |
| Signal Level | 800mV nominal |
| DC Offset | 0V ±0.5V |
| Rise/Fall Time | 900ps nominal @ 270Mb/s < 270ps @ 1.485Gb/s |
| Overshoot | < 10% of amplitude |
| Return Loss | > 15dB up to 1.485Gb/s |
| Wideband Jitter | < 0.2UI |
Analog Audio Output | |
|---|---|
| Number of Outputs | 4 |
| Type | Balanced analog audio |
| Connector | 12-pin removable terminal block |
| Impedance | 66Ω |
| Frequency Response | ±0.1dB, 20Hz to 20kHz |
| THD | < 0.005% |
| Channel Phase Differential | ±1° |
| SNR (weighted) | > 85dB |
| Output Level Adj. | -20dB to 3dB |
| Maximum Level | 24dBu into 10kΩ loads |
AES Audio Outputs | |
|---|---|
| Standard | |
| Balanced | AES3-1992 |
| Unbalanced | SMPTE ST 276 |
| Other | Dolby® E compatible |
| Number of Outputs | 4 regenerated (selectable for balanced or unbalanced) |
| Connector | 12 pin terminal strip |
| Return Loss | > 15dB, 1MHz to 6MHz |
| Signal Level | |
| Balanced | 2V p-p ±0.1V |
| Unbalanced | 1V p-p ±0.1V |
| Resolution | Up to 24 bits |
| Sampling Rate | 32, 44.1, 48kHz |
| Jitter | < 0.1UI |
| Impedance | |
| Balanced | 110Ω |
| Unbalanced | 75Ω |
Optical Input | |
|---|---|
| Number of Inputs | 1 |
| Connector | Female SC/PC, FC/PC |
| Wavelength | 1270nm to 1610nm |
| Maximum Power | 0dBm |
| Optical Sensitivity | -23dBm |
| High Standard Sensitivity | -28dBm |
Electrical | |
|---|---|
| Voltage | +12V DC |
| Power | 13 Watts |
| EMI/RFI | Complies with FCC Part 15, Class A, EU EMC Directive |
Physical | |
|---|---|
| Number of Slots | 1 |
Ordering Information
| 7707ADVR-HD | Analog, SDI or HD-SDI & analog/AES audio Fiber Receiver |
|---|
Ordering Options | |
|---|---|
| Notes | • Rear plate and fiber connector must be specified at time of order - eg: [model]+SC+3RU |
| Connector Suffix | |
|---|---|
| +SC | SC/PC |
| +FC | FC/PC |
| Rear Plate Suffix | |
|---|---|
| +1RU | 1RU rear plate for use with 7701FR Multiframe |
| +SA | Standalone Enclosure Rear Plate |
| +3RU | 3RU rear plate for use with 350FR, 7700FR-C or 7800FR Multiframes |
Enclosures | |
|---|---|
| 350FR | Portable Multiframe which holds 7 single slot modules |
| 7700FR-C | 3RU Multiframe which holds 15 single slot modules |
| 7800FR | 3RU Multiframe which holds 15 single slot modules |
| 7701FR | 1RU Multiframe which holds 3 single slot modules |
| S7701FR | 7700 Series Standalone Enclosure |