*********************************************************
* This firmware is for the following products:          *
* ---------------------------------------------         *
* HD9010TM         HD9010TM-IRIG                        *
*********************************************************

version 2.0 build 564  (May 29, 2015)
---------------------------------------
- Reworked 6Hz locking mechanisms
 - Added Debug Window code to report 6Hz and 30Hz locking status
- Fixed accuracy of parallel port 6Hz and 30Hz locking
- Readjusted 24 to 30 cross jamming triggers
- Fixed Aux LTC input reader modes and Generator Time anomalies  
- Corrected first pass into the menu system's sub menu does not flash display to indicate correct setting 
- Resolved crashes when entering GEN MODE menu item  
- Fixed crashes when ATC reader type is vitc but input ATC type is ltc 
- Resolved GTM won't stop at no code mute or hold condition   
- Fixed ATC generator is turned on after reboot  

- Corrected won't boot if COM1 baud rate set below 2400 
- Unit crashes if a window falls below the bottom of the screen 
- ATC Generator turns on if ATC Generator type is changed  
- ATC Reader type always functions as LTC+VITC 
- Video LED stays on when input video disconnected  
- ATC Reader Modes and "No Code Run/Hold" functionality corrected 
- GUB value not consistent when GEN MODE is time data 
- ANC GEN cannot be turned on at some conditions 
- Corrected GTM won't stop completely at no code mute or hold condition 
- menu display timer incorrectly affecting non menu display modes 
- Removing the source time code mutes the output time code for only a few seconds 
- Anc Generator falsely creates a VITC2 packet when the GEN ATC TYPE is set to LTC only 
- On power up the first pass into the menu system's sub menu does not flash display to indicate correct

version 2.0 build 241 (April 15, 2009)
---------------------------------------
- Fixed preset mapping size bug
- Fixed HANC inserter not handling existing RP-188 (SMPTE-12M-2) packets that appear BEFORE the audio control packets
- Added VANC inserter On/Off Menu item
- Fixed 720P video standards randomly phase locking to the genlock input, only works with bi-level inputs
- Added 1080P/30 support

Version 2.0 build 138 (June 6, 2006)
-------------------------------------
- Added drop-frame conversion mode
- Panel lockout process now involves SHIFT key
- Added "VID:" current video standard display
- Added IRIG no code present dynamics
- Corrects NVRAM storage and restoration problems
- Improved metadata protocol connectivity
- Corrected display issues
- Corrected COM1 baud rate issue  

Version 2.0 build 37 (July 12, 2005)
-----------------------------------------------
- Added GPI transmission via RP-188 timecode support for 6 inputs. Valid on 7700PH4 boards
- Added to the Front panel a GPI, COM1, and COM2 status display
- extended the GPI status displays to 8 inputs.  
- Assigned default functions for 8 GPIs (consult manual)


Version 2.0 build 01 (May 30, 2005)
-----------------------------------------------
- Initial release for Harware revision REV 2 (7700PH4)
- This and later versions will have dual hardware revision support.  
  With the setting of the appropriate environment variables, they 
   will run on both REV1 and REV 2 type hardware

Version 1.2 build 201 (January 12, 2005)
----------------------------------------
- corrected a rare IRIG reader burn in bobble issue

Version 1.2 build 190 (January 4, 2005)
---------------------------------------
- added IRIG timecode reading capabilities (requires IRIG option hardware)
- added IRIG information insertion into the RP-188 ANC data generator
- added the capability to read back the ANC data containing the IRIG information
- corrected a small drift error in the irig reader

Version 1.2 build 44 (August 19, 2004)
--------------------------------------
- added tri level sync genlock support
- added No Code Jam support
- fix for a jamming offset issue

Version 1.2 build 1 (May 5, 2004)
---------------------------------
- fix for jamming between different timecode rates

Version 1.1 build 66 (February 25, 2004)
----------------------------------------
***NOTE - This version of firmware requires new CPLD code to be loaded ***

- fix for offset issue
- fix for output rate of Auxillary LTC generator
- fix to support and automatic switch between 1:1 and 1:1.001 standards

Version 1.0 build 2065 (February 6, 2004)
-----------------------------------------
- fix for video standard issue

Version 1.0 build 1997 (December 10, 2003)
------------------------------------------
- fix to pass audio through the RP-188 inserter

Version 1.0 build 1989 (November 14, 2003)
------------------------------------------
- fix for bypass power up issue

Version 1.0 build 1988 (November 12, 2003)
------------------------------------------
- first release