******************************************************* * This firmware is for the following products: * * ----------------------------------------------------* * 500DCDA-HD * ******************************************************* version 4v10_1 (September 29, 2009) --------------------------------------- -Correct CEA-608 CC underflow issue. -Correct CDP out of range 'set pen location' issue. Version 4.07 build 1 (July 18, 2007) --------------------------------------- - Improved Vistalink support - Correction HANC area for audio in 625 mode - Removed the tailgated image existed at two thirds of the last line of the 1st field in 525 mode Version 4.04 build 6 (November 7, 2006) --------------------------------------- - Improved Vistalink support - Improved 3:2 pulldown locking - Correction to timecode reading - Correction to reported delay - Correction to 4:3 markers - Added support for 720p/50, 1080p/30, 1080p/29.97, 1080p/24, 1080p/23.98 and 1080p/25 - Added Wide Screen Signalling generation as per ITU-R BT.1119-2 Annex 1 Version 2.03 build 17 (September 26, 2005) ------------------------------------------ - added support for revision D hardware Version 2.2 build 47 (June 22, 2005) ------------------------------------ - fixed some preset save/recall issues. - updated to the latest vistalink interface. The DCDA-HD now: - supports all CCM parameters - is FC upgradeable - has a new MOD ID of 17 - can recall presets via vistalink. - fixed 625 CC line selection. - fixed an issue with reading 625 CC field 2 data. - fixed an issue with 1035i - rewrote Progressive to Interlace converter to solve vertical line on screen around sample 412. - fixed issue with bad data on last pixel of the line when 625 output and no video on input - removed Grat generation from output when input is SD. - added serial port command to make selection of output video easier. (ovm) - changed VHDL rev info to 1.1 - changed output video Mux to be more useful. Version 2.01 build 1 (March 7, 2005) ------------------------------------ - fix for re-locking issue after loosing video on input Version 2.00 build 24 (September 1, 2004) ----------------------------------------- - fix for 480p video standard Version 2.00 build 1 (August 24, 2004) -------------------------------------- - fix for 625 video standard issue Version 2.00 build 0 (August 19, 2004) -------------------------------------- - added closed caption monitoring support - added set minimum delay control - added output video limiter - fix for zero phase offsets - fix for frame buffer issue at low delays - fix for aspect ratio issue - fix for 3:2 Pull Down locking to RP188 - fix for video input issue - H and V filter range has been increased Version 1.01 build 292 (May 12, 2004) -------------------------------------------------- - added support for doing sets in VistaLink - fix for OSD issue Version 1.01 build 287 (May 11, 2004) -------------------------------------------------- - added support for doing sets via VistaLink Version 1.01 build 245 (February 16, 2004) --------------------------------------------------------- - added support for various 60Hz standards - 1080i/60 - 1035i/60 - 720p/60 - 480p/60 - 1080p/24 - 1080p/23.98 Version 1.01 build 131 (November 28, 2003) ----------------------------------------------------------- - fix for video and audio delay - fix for black line seen on screen when NTSC pedestal turned on Version 1.01 build 14 (October 22, 2003) ----------------------------------------------------- - fix for field inversion issuer on SD output - fix for VITC in all HD input formats - fix for SD input detection - fix for SD input's closed captioning, VITC and audio - fix for the Serial Status Protocol Version 1.00 build 98 (July 29, 2003) ------------------------------------------------ - added auto select the output standard based on the input standard - the STD (NTSC/PAL) jumper now only selects output standard for when there is no input video Version 1.00 build 96 (July 18, 2003) ------------------------------------------------ - fix for 1080i50 downconverted to 720i576 Version 1.00 build 71 (April 21, 2003) ------------------------------------------------- - first release - know issue: SD input not functioning, HD OK